****Beds with built in magnets are assembled to order and have a minimum of one week processing time****
****Beds with built in magnets must ship with a GROUND transportation shipping service, if you do not pick a ground service your order will be adjusted and you will be invoiced if there is a price difference****
Cast Aluminum Printer Bed for Ender 3 S1 and S1 Pro Printers
These cast aluminum 3D printer beds make for a superior print bed, far exceeding what comes standard on most consumer 3D printers in terms of flatness, rigidity and stability.
This bed incorporates the following features:
-CNC Machined, to ensure all features are exactly where they
should be
-Premium cast aluminum plate, we only use MIC6, K100S, and ATP-5
cast plate to make our beds from.
-Machined perimeter - no raw saw cut edges, giving you a
nice finished appearance
-All holes are precisely sized and counterbores made exactly
the size they need to be.
-Build surface locating pins - When using a magnetic build
surface, out locating pins (screws) aid you to placing the removable build
surface, every time.
-Thermal Sensor groove milled into the top surface. This
positions the sensor as close as possible to the build surface, thereby giving
the best possible temperature reading.
-Thermal fuse and earth ground mounting locations – we provide
tapped holes to mount a thermal fuse and an earth ground lead, to facilitate the
safest installation possible.
-An additional 15mm on the back edge of the bed to allow for
attachment of cable clamps, cable drag chains. In this bed extension there are
3 sets of M3 holes 25mm apart for the clamps or drag chains to attach to.
-This bed supports mounting with four leveling screws, like the factory configuration. Or three point leveling, to match the West Coast Robotics carriage plate.
-Hardware included - We include the required hardware; New
M4 leveling screws, washers. Additionally we include the build surface backstop
pin (screws) and screws for mounting a thermal fuse and earth ground.
Specs
Printable area: 235mm x 235mm
Thickness: 6.35mm ¼”
Overall size: 235mm x 250mm
Flatness: Standard grade beds have a flatness of 0.10mm or better, every bed plate we make is CMM inspected for flatness before packaging.
This bed plate should fit the following printers
Ender 3 S1
Ender 3 S1 Pro
Magnet Version of this bed
This bed plate offers the following features
-Thermistor slot in the top to allow the end user to glue in a thermistor to measure the actual bed temperature near the build surface. This slot will cause no problems with the print surface and it commonly done on some high end corexy printers and commercial grade 3D printers.
-An additional 15mm on the back edge of the bed to allow for attachment of cable clamps, cable drag chains. In this bed extension there are 3 sets of M3 holes 25mm apart for the clamps or drag chains to attach to.
-Build surface stop pins have been added via two tapped holes in the bed extension and screws that are included with the bed. These allow you to bump your magnetic build surface sheet up against them before lowering it on to the magnetic surface. This provides a more consistent placement of your magnetic build surface with ever use.
-This bed supports mounting with four leveling screws, like the factory configuration. Or three point leveling, to match the West Coast Robotics carriage plate.
-New quality M4 mounting hardware is included with each bed, included with this is 4 M4 flat head screws, 4 flat washers and 4 nuts so you can rigidly attach the mounting screws so they do not spin when used with leveling knobs.
-12 samarium cobalt magnets, placed in the top surface flush or just barely below flush with the top surface. With 3lbs of pull each and a temp rating up to 300*C. These beds are made to order and have about a one week processing time.
235mm X 235mm Printer Area
235mm X 250mm X 6.3mm Overall Dimensions
Weight: 1.06kg (2lb 5.2oz) with hardware kit
Flatness - Standard grade beds have a flatness of 0.10mm or better, every bed plate we make is CMM inspected for flatness before packaging.
Ender 3 S1
Ender 3 S1 Pro
